Flange connection (flange, joint) consists of a pair of flanges, a gasket and several bolts and nuts.
The gasket is placed between the sealing surfaces of the two flanges. After the nut is tightened, the specific pressure on the surface of the gasket will deform when it reaches a certain value, and fill the unevenness on the sealing surface to make the connection tight and leak-proof.
Flange connection is a detachable connection. According to the connected parts, it can be divided into container flange and pipe method; according to the structure type, there are integral flange, looper flange and threaded flange. Common integral flanges include flat welding flanges and butt welding flanges.
Flat welding flanges have poor rigidity and are suitable for occasions where the pressure is p≤4MPa; butt welding flanges, also known as high neck flanges, have higher rigidity and are suitable for occasions with high pressure and temperature.
There are three types of flange sealing surfaces: flat sealing surface, suitable for occasions where the pressure is not high and the medium is non-toxic; concave and convex sealing surface, suitable for occasions with slightly higher pressure;
Tongue and groove sealing surface, suitable for flammable, explosive, toxic media and high pressure occasions.
Butt welding flange gasket is a ring made of material that can produce plastic deformation and has a certain strength. Most of the gaskets are cut from non-metallic sheets, or made by professional factories according to the specified size, and their materials are asbestos rubber sheets, asbestos sheets, polyethylene sheets, etc.;
There are also metal clad gaskets made of thin metal plates (white iron, stainless steel) wrapped around non-metallic materials such as asbestos; there is also a wound gasket made of thin steel strips and asbestos strips.
Ordinary rubber gaskets are suitable for occasions where the temperature is lower than 120 °C; asbestos rubber gaskets are suitable for occasions where the temperature of water vapor is lower than 450 °C, the temperature of oil is lower than 350 °C, and the pressure is lower than 5MPa. The most commonly used medium is acid-resistant asbestos board.
In high-pressure equipment and pipelines, lens-type or other-shaped metal gaskets made of copper, aluminum, 10-gauge steel, and stainless steel are used.
The contact width between the high-pressure gasket and the sealing surface is very narrow (line contact), and the processing finish of the sealing surface and the gasket is high.
The low-pressure small diameter has a wire flange, and the high-pressure and low-pressure large diameter use welded flanges. The thickness of the flanges and the diameter and number of connecting bolts are different for different pressures.
The gasket is placed between the sealing surfaces of the two flanges. After the nut is tightened, the specific pressure on the surface of the gasket will deform when it reaches a certain value, and fill the unevenness on the sealing surface to make the connection tight and leak-proof.
Flange connection is a detachable connection. According to the connected parts, it can be divided into container flange and pipe method; according to the structure type, there are integral flange, looper flange and threaded flange. Common integral flanges include flat welding flanges and butt welding flanges.
Flat welding flanges have poor rigidity and are suitable for occasions where the pressure is p≤4MPa; butt welding flanges, also known as high neck flanges, have higher rigidity and are suitable for occasions with high pressure and temperature.
There are three types of flange sealing surfaces: flat sealing surface, suitable for occasions where the pressure is not high and the medium is non-toxic; concave and convex sealing surface, suitable for occasions with slightly higher pressure;
Tongue and groove sealing surface, suitable for flammable, explosive, toxic media and high pressure occasions.
Butt welding flange gasket is a ring made of material that can produce plastic deformation and has a certain strength. Most of the gaskets are cut from non-metallic sheets, or made by professional factories according to the specified size, and their materials are asbestos rubber sheets, asbestos sheets, polyethylene sheets, etc.;
There are also metal clad gaskets made of thin metal plates (white iron, stainless steel) wrapped around non-metallic materials such as asbestos; there is also a wound gasket made of thin steel strips and asbestos strips.
Ordinary rubber gaskets are suitable for occasions where the temperature is lower than 120 °C; asbestos rubber gaskets are suitable for occasions where the temperature of water vapor is lower than 450 °C, the temperature of oil is lower than 350 °C, and the pressure is lower than 5MPa. The most commonly used medium is acid-resistant asbestos board.
In high-pressure equipment and pipelines, lens-type or other-shaped metal gaskets made of copper, aluminum, 10-gauge steel, and stainless steel are used.
The contact width between the high-pressure gasket and the sealing surface is very narrow (line contact), and the processing finish of the sealing surface and the gasket is high.
The low-pressure small diameter has a wire flange, and the high-pressure and low-pressure large diameter use welded flanges. The thickness of the flanges and the diameter and number of connecting bolts are different for different pressures.
Next£ºHow to choose flanges?
Previous£ºÒÑÊǵÚÒ»¸ö£¡
Product CenterProduct Center
Steel Flange
Stainless Steel Flange
Carbon Steel Flange
ANSI Standard Flange
JIS B2220 Steel Flange
EN1092 Steel Flange
TEL£º15861609828
TEL£º15861609828
QQ£º707378883
E-mail£º707378883@qq.com
Address£ºJiangyin City Zhouzhuang Town Nijia lane village Hongta Road No. 15